 |
Roof cricket that is easy to use and reflect actual construction size for 1/2:12 sloped insulation. made with complex trig formulas. easily gives you slopes in all directions. Roof hosted. INSTRUCTIONS: place on roof surface. Adjust Li & Hi (i.e. lenght and depth of cricket) in decimal FT and align to the walls. only works on right angles. |
No rating |
Product Version: Unknown
1076 downloads
|
|
 |
150mm random WeatherBoard siding |
|
Product Version: Unknown
7579 downloads
|
|
|
 |
Simple Profile created for a sloping metal parapet cap. This profile is meant to be hosted on a wall and works well with the wall sweep tool. It is not parametric though I don't even know if profiles can be. It hosts at about it's midpoint in height so that it partially goes down to cover the top of the wall and extends partially above. It is about 4" high on the exterior face and slopes down 1" to the back side. |
|
Product Version: Revit Architecture 2011
7965 downloads
|
|
|
 |
AA-Ridge of Roofs |
|
Product Version: Revit Building 8.1
11575 downloads
|
|
|
 |
Additive Tapered Insulation |
|
Product Version: Unknown
2368 downloads
|
|
|
 |
Additive Tapered Insulation-L shape |
|
Product Version: Unknown
1551 downloads
|
|
|
 |
adjustable downspout |
|
Product Version: Unknown
8535 downloads
|
|
|
 |
Asphalt Shingles |
|
Product Version: Unknown
8552 downloads
|
|
|
 |
Asphalt Shingles |
|
Product Version: Unknown
8560 downloads
|
|
|
 |
Australian Cee Girts - Custom Orb Wall Cladding |
|
Product Version: Unknown
2092 downloads
|
|
|
 |
Australian Cee Girts - Trimdek Wall Cladding |
No rating |
Product Version: Unknown
2497 downloads
|
|
|
 |
Australian Zed Girts - Custom Orb Cladding |
No rating |
Product Version: Unknown
2243 downloads
|
|
|
 |
Australian Zed Girts - Trimdek Wall Cladding |
No rating |
Product Version: Unknown
2035 downloads
|
|
|
| |
|
No rating |
Product Version: Unknown
2908 downloads
|
|
|
 |
This is a NON-parametric fan, but can be eddited easily |
No rating |
Product Version: Revit Architecture 2016
1201 downloads
|
|
|
 |
Barrel Roof Tile |
|
Product Version: Unknown
32115 downloads
|
|
|
 |
Detail component Batt Insulation
Batt Insulation with switch to allow for tapered ends for use near eaves or in over the purlin installation in pre-engineered metal buildings. |
|
Product Version: Revit Architecture 2012
8653 downloads
|
|
|
 |
Batt Insulation |
|
Product Version: Unknown
13838 downloads
|
|
|
 |
Parameter to change insulation to any width. Automatically adjusts to any length, unlike the out of the box insulation command. |
No rating |
Product Version: Revit Architecture 2015
2151 downloads
|
|
|
 |
Beirado Canto |
|
Product Version: Unknown
4092 downloads
|
|
|
 |
Roof to building expansion joint. Load profle; Create New fascia
Use Roof fascia to integrate work. |
No rating |
Product Version: Unknown
376 downloads
|
|
|
 |
Roof to building expansion joint. Load profle; Create New fascia
Use Roof fascia to integrate work. |
|
Product Version: Unknown
212 downloads
|
|
|
 |
Butler Pre-Engineered Metal Building MR-24 Standing Seam Roof Panel Adj Length. |
|
Product Version: Unknown
8052 downloads
|
|
|
 |
Parametric: - support numbers - overhang |
|
Product Version: Revit Architecture 2009
11537 downloads
|
|
|
 |
Cimalha-Canto |
No rating |
Product Version: Unknown
2240 downloads
|
|
|
 |
This is for anyone looking for a more realistic tiled roof. Array horizontal model lines up the face of your roof at a spacing of 18", select peak_valley, gable, valley_valley, etc depending on what type of face it is, and place the line-based generic model family by line-selection. Height of tile is adjustable (good for fitting in last row). Made for a 5/12 slope, but will probably work with others. Also included is the jpeg for the material I used. Renders beautifully. |
|
Product Version: Unknown
25420 downloads
|
|
|
| |
This is for anyone looking for a more realistic tiled roof. Array horizontal model lines up the face of your roof at a spacing of 18", select peak_valley, gable, valley_valley, etc depending on what type of face it is, and place the line-based generic model family by line-selection. Height of tile is adjustable (good for fitting in last row). Made for a 5/12 slope, but will probably work with others. Renders beautifully. |
No rating |
Product Version: Unknown
1960 downloads
|
|
|
| |
this was created as a beam, so you can use it by creating a beam system. Let me know if you find a way to make it parametric |
No rating |
Product Version: Revit Architecture 2009
2210 downloads
|
|
|
 |
this was created as a beam, so you can use it by creating a beam system. Let me know if you find a way to make it parametric |
|
Product Version: Revit Architecture 2009
10466 downloads
|
|
|
 |
Hi there Here are two families of the same ‘crested ridge tiles’. One been build using the generic model line base template so you can drag it along the line with to control points but the tiles sometimes over lap, the second family been build using the generic model template and you control it either by the length or by the number of tiles. In both families you can control the angle of the tile and the material. nirim |
No rating |
Product Version: Revit Architecture 2011
4444 downloads
|
|
|
Search