 |
Two sink basins, soap dispenser, hand dryer, and one trash unit in the middle. Please rate and comment. |
|
Product Version: Revit MEP 2010
4699 Downloads
|
|
 |
This is a fully parametric sink with shared faucet and drains. |
|
Product Version: Revit Architecture 2013
65345 Downloads
|
|
|
 |
Generic simple parametric bathroom sink without drainage pipes. Units are in centimeters. |
|
Product Version: Revit Architecture 2017
63772 Downloads
|
|
|
 |
Two sink basins, soap dispensers, hand dryers, and one trash unit on the left side. Please rate and comment. |
|
Product Version: Revit MEP 2010
2477 Downloads
|
|
|
 |
metric sink with cupboard |
No Rating |
Product Version: Unknown
4293 Downloads
|
|
|
 |
Simple Wall Hosted Eye Wash sink with adjustable height. |
|
Product Version: Unknown
14748 Downloads
|
|
|
 |
Simple, generic 8"x8"x8" floor sink with dome strainer. Toggle on/off full, half or 3/4 grate. 3D find and 2D medium and coarse representaion. |
|
Product Version: Revit MEP 2010
6481 Downloads
|
|
|
 |
27" w X 20" deep x 36" tall pedestal sink - loosely based upon American Standard Retrospect. Not refined - but will do for a quick residential bathroom perspective. |
|
Product Version: Revit Structure 2009
97015 Downloads
|
|
|
 |
This is my first try at it... but it got the job done which is to have a family to connecto to from a single cold water line under sink to hot water service line 1/2" diameter. |
|
Product Version: Revit Structure 2011
15844 Downloads
|
|
|
 |
Stainless Steel Kitchen sink with Drainboard 1200mm long. |
|
Product Version: Unknown
68180 Downloads
|
|
|
 |
It is a corner sink base cabinet, took the imperial library corner cabinet, and made some changes for a house I was working on. |
|
Product Version: Revit Architecture 2009
13598 Downloads
|
|
|
 |
Sink Base Dimensions: 2'1.5"D, 2'1.75" W, 2'10.5" H
Faucet Dimensions: 13" W (8" spread)3" deep, 11.25" H
Designed in Revit LT 2015 |
No Rating |
Product Version: Revit Architecture 2015
3440 Downloads
|
|
|
 |
A bathroom family that i use for my bathrooms, comprising of a curved sink on vanity top, mirror with light above, and base cabinet built in. |
|
Product Version: Revit Architecture 2015
33838 Downloads
|
|
|
 |
Simple 3d sink, wall based, non-parametric |
|
Product Version: Unknown
6569 Downloads
|
|
|
 |
Bathroom sink with lower cabinet and mirror |
No Rating |
Product Version: Revit Architecture 2020
2268 Downloads
|
|
|
 |
Two sink basins, with soap dispensers, hand dryers, and one trash unit on the right side. ADA complient. Please rate and comment. |
|
Product Version: Revit MEP 2010
2780 Downloads
|
|
|
 |
basic laundry sink |
No Rating |
Product Version: Unknown
14014 Downloads
|
|
|
 |
Wall Mounted Service Sink |
|
Product Version: Revit Architecture 2008
12613 Downloads
|
|
|
 |
a porcelain sink made at NOHS |
|
Product Version: Revit Architecture 2014
11998 Downloads
|
|
|
 |
20" Glass sink with waterfall faucet |
|
Product Version: Revit Architecture 2012
9093 Downloads
|
|
|
 |
parametric wall mounted sink |
No Rating |
Product Version: Unknown
12316 Downloads
|
|
|
 |
If you want to get away from having Bench Tops/Counter Tops with Parametric holes for Sinks
I have added a piece of Bench Top to my Sinks; it is fixed Parametrically so that for a bigger or smaller sink the bench part adjusts with it.
The Bench part to my Sink has very specific parameters, the Bench Thickness is "Instance", it has a "Yes/No" Type parameter, (always switched off.) plan view is "Unticked", it is attached to the "Top of Counter Top" reference plane as is the Sink, the part is shaped with rounded corners (As the Counter Cut Outs would be)
The sink is added into the Project just as normal, just place it onto your Counter Top in the position you want; At this point your counter Top will pass through you sink!
Now all you have to do is use the REVIT "Cut Geometry" sellect your Counter Top, then the Sink and "WHALLA", you now have your "Counter Top" with a Cut Out, this approach allows you to move the sink and the cut out moves with it, if you delete the sink the Bench is repaired, (No Hole). (If you Hide the Sink Your Bench Top should have a Hole in it)
|
|
Product Version: Revit Architecture 2012
5400 Downloads
|
|
|
 |
One basin sink with soap dispenser, and hand dryer, all in one unit. Same as the 353631 & 353632 except is doesn't have the trash can. Please rate and comment. |
|
Product Version: Revit MEP 2010
3283 Downloads
|
|
|
 |
This is a standard Kraus 14 Inch Glass Vessel Bathroom Sink with different colors of Mounting Ring. Available colors:Chrome;Gold;Oil Rubbed Bronze;Satin Nickel.
|
|
Product Version: Revit Architecture 2012
20024 Downloads
|
|
|
 |
metric sink |
No Rating |
Product Version: Unknown
1590 Downloads
|
|
|
 |
Lavadero de granito para lavanderiaGranite laundry sink |
|
Product Version: Revit Building 9.1
25129 Downloads
|
|
|
 |
Cutting Board Sink
Made at NOHS |
No Rating |
Product Version: Unknown
3842 Downloads
|
|
|
 |
This is a scrub sink based on a particular model found on www.dremed.com. It can be either single- or double-station and has a knee-action faucet valve. |
|
Product Version: Revit Architecture 2009
6554 Downloads
|
|
|
 |
This is the standard L counter family that I modified to be able to hide the sink hole and to angle the sides independantly. This will let you have more counter options or splice between families using 45 degree angle or other. |
No Rating |
Product Version: Revit Architecture 2013
14066 Downloads
|
|
|
 |
Kohler - K-3335
Undertone� Extra Large Deep Undercounter Kitchen Sink, 17 7/8" x 17 7/8" x 9 1/2", Rounded Basin |
|
Product Version: Unknown
5663 Downloads
|
|
|
Search