Fixed exterior aluminum window 4 panes wide x 2 panes high

Product Version: Revit Architecture 2008

14795 Downloads

Fixed Skylight

No Rating

Product Version: Revit Building 5.1

12712 Downloads

Fixed Archtop

No Rating

Product Version: Revit Building 5.1

1416 Downloads

This window family is fully parametric.

Product Version: Revit Architecture 2008

19085 Downloads

This family will automatically generate the right length desk for the number of seats required. Seats are set @ 30" apart.

Width of the desk can be changed dynamically

Product Version: Unknown

1889 Downloads

NOHS craftman style single window made by Scott

Window Casement, Wood Windows. Openings, Special Window. 

Product Version: Unknown

24375 Downloads

This is a tranaction window with a transaction drawer based upon the Diebold model 131-85 Retail Window with 121-30 transaction drawer (5'-0"x5'-0" window opening). There is also a microphone modeled on the interior transaction surface. This is similiar to what you would see in a pharmacy drive through. I did not make this parametric because I did this for a specific instance.

Product Version: Unknown

22671 Downloads

Fixed Plastic seats mounted on tube steel.  Seating and length are parametric.

Product Version: Revit Architecture 2011

8580 Downloads

The window frame is fixed on a projecting rcc sill and lintel outside the opening to allow 100% openable sliding shutters.

No Rating

Product Version: Revit Architecture 2011

912 Downloads

Parametric window surround including the ability to show a dashed line above the window indicating flashing.

Product Version: Unknown

10255 Downloads

In the Imperial Labrary I noticed that the Double Compartment Sink had the Hot and Cold water connections were reverced so I fixed them. This sink is correct.

Product Version: Unknown

4217 Downloads

This is a parametric detail component for a casement window section. The family is adjustable for window rough opening height and wall thickness.

This is base on the Eagle Window line.

This was created in Revit 2016

Product Version: Unknown

6200 Downloads

Fixed Round Top

Product Version: Revit Building 5.1

5233 Downloads

Fixed Round Top

No Rating

Product Version: Revit Building 5.1

2938 Downloads

NOHS, stained glass window, contemporary window, red and black window

Product Version: Unknown

7829 Downloads

NOHS, stained glass window, contemporary window, red and black window

Product Version: Unknown

4020 Downloads

3 side by side fixed panel windows stacked 2 high (6 windows all up)

Product Version: Revit Architecture 2010

24822 Downloads

This window family is fully parametric. You can adjust the angle of the opening, panel/frame/mullion material, the size of the mullion and frame and the thickness of the panel.

Product Version: Revit Architecture 2008

41548 Downloads

This window was used in a wall with brick veneer and is not adjustable.  There is an area of window left out to allow for a dbl door to be inserted.  This will allow for the window and door to be tagged seperately.

Product Version: Revit Architecture 2011

17000 Downloads

This default window set up with different type of brick sill where you can choose which one and you can make a double hung or sliding window infill with glass. also you can close gap the brick sill using stud wall to 1mm. It will save you time set up the brick sill. Make sure save as before you change the type of window. This is default only window.

Product Version: Unknown

33120 Downloads

An adjustable louvre window where you specify the maximum span for the louvre and the window will create the required number of bays. You can also specify the usual, size of louvres, angles, free air, material etc etc...

Product Version: Unknown

41411 Downloads

A window with a fully parametric brick arch.  This took quite a while to figure out, but I wanted to share it with anyone that wanted it.  The brick arch is fully parametric in that it will adapt to the width, height, or arch height of the window.  The number of bricks will also adapt depending on how wide/tall the window is.  The window itself can be adapted as needed.  Note.  This arch part of the window is made to be configured by the height of the arch, not by a radius.  I did this since I wanted to be able to specify a specific height for the arch to match brick coursing.   And of course feel free to change the window to an opening/door/whatever.  Just make sure you keep the main parameters.

Product Version: Revit Architecture 2009

21677 Downloads

This is a circle top window with a brick sill , a single row of soldier course around entire window and a KEYSTONE head peice.

Product Version: Unknown

35477 Downloads

fixed 2 with trapzoid top

No Rating

Product Version: Unknown

1981 Downloads

skylight, 2x3 fixed, with wood trim

Product Version: Unknown

6077 Downloads

Modern/Contemporary style window with adjustable muntin/mullion placement. Window can be set next to similar windows to make different arrangements.

All windows shown in thumbnail are the same family.

Product Version: Revit Architecture 2018

18216 Downloads

This is a picture window with an awning window above. The trim width is fully parmetric for the interior and exterior. There are only a few family types (sizes) created so feel free to add to it.

Product Version: Unknown

7297 Downloads

H. Mtl. Door w/ Adjustable Width and Fixed Frame depth

No Rating

Product Version: Unknown

883 Downloads

window bars for window of size 1500 by 900 mm

Product Version: Unknown

15882 Downloads

I was given the task to get the legend components to read text or type mark and have the Legend and the floor plan both reading same tag text!What it does is let me label the window say W1 in the window family for the WINDOW TYPE. Add a window tag it reads W1 in the tag. Finally when I insert that window into the window legend I have a text defaulty in that family to read the type so it says under the window W1 and any time I read number my window tags they all will update in a blink of an eye!Used for any Legend Component like Door, Window, Wall types!I've read in these forums that people are not using the Legend for WALL TYPES or Window Elevations, Door Elevations. I know you still can't Dim. walls in the legend but you can link a text into any item to report that item TYPE in the legend, to schedule, in the plans and change it once!Use Model text in the family to link to a shared parameter, then in the tag's label link that text to the shared parameter and you have yourself a link text and label tag!Copy Paste the Model Text into any window family you might have now by using model text in that window family, use a shared parameter to link that text to and link a window tag family text label to that shared parameter BAM BAM! You got it!

Product Version: Revit Architecture 2008

4796 Downloads