This is a generic door family provided by www.Revitopia.com. It utilizes embedded families to allow concentrated design on the pieces that make up a door with minimal breaking. Its a result of door development for the designer/architects use.

Product Version: Unknown

1167 Downloads

Parametric hollow metal doors w/ un-equal leafs and customized door schedule. Due to the asymmetrical nature of this type of doors; Ideally, there should have two families, one for the left active door, one for the right. This one is only show a quick way for how to create this type of door. If you like it, you can download the door families in  the drawings "Adjustable Hollow Metal Doors for CMU and Stud Walls", and "Adjustable Hollow Metal Doors-Improved Version" as bases, adding/modify parameters as you need, and creat your own set of parametric door families. Enjoy!

Product Version: Revit MEP 2009

7046 Downloads

Improved parametric hollow metal doors from my post dated August 31, 2011.You can open the "Door Schedule View", switching "Door Type" from #1 thru #4, and watching the door panel changes on 3 D view.You can also check/unckeck "Exterior Door", to swith the "(5) GLASS" from "SG" - safety glass, to "SGI" - safety glass-insulated.If you like it, you can download the door families in  the drawing mentioned above as bases, adding parameters shown here, and creat your own set of parametric door families. Enjoy!

Product Version: Revit Architecture 2009

10937 Downloads

Improved parametric hollow metal doors from my post dated August 31, 2011.You can open the "Door Schedule View", switching "Door Type" from #1 thru #4, and watching the door panel changes on 3 D view.You can also check/unckeck "Exterior Door", to swith the "(5) GLASS" from "SG" - safety glass, to "SGI" - safety glass-insulated.If you like it, you can download the door families in  the drawing mentioned above as bases, adding parameters shown here, and creat your own set of parametric door families. Enjoy!

Product Version: Revit Architecture 2009

8570 Downloads

I was fed up with bad door families so I made this fully parametric door that opens and closes.

Product Version: Unknown

24401 Downloads

I was fed up with bad door families so I made this fully parametric door that opens and closes.

Product Version: Unknown

13834 Downloads

Parametric colonial nested door families:

4x Panel types,

4x Ironmongery types.

Product Version: Revit Architecture 2015

1509 Downloads

Revit 2019.  This Garage door is compiled from a few different families found on Revit city.

Product Version: Revit Architecture 2018

1220 Downloads

Fully Parametric 2 Panel Bifold Door. All components are nested families. Hardware included

Product Version: Unknown

45766 Downloads

Exterior Entrance Pair doors with pair side lights. 3 levels of detail, Detail level FINE show packers and jambs, heads and sill. Door panel material are changeable. Door created by nested families

Product Version: Unknown

11720 Downloads

Fully parametric modern barn-style door. All components are nested families. Default materials as shown in image can be changed in material parameters.

Product Version: Revit Architecture 2018

26636 Downloads

Families of Doors

Family changes and 2010 update 5/16/09 See Notes.

Product Version: Revit Architecture 2010

13925 Downloads

Single Door - Fully Parametric - All elements are nested families and are completely parametric. Full Lite, Half Lite, and Flush Panel doors included. All Hardware included.

No Rating

Product Version: Unknown

3471 Downloads

Fully Parametric 4 Panel Bifold Door. All components are nested families. Hardware included

Product Version: Unknown

32873 Downloads

Automatic Sliding Door, parametric

Check more families at: http://revitdb.pt.vu/

Product Version: Revit Architecture 2013

52455 Downloads

Double Door - Fully Parametric - All elements are nested families and are completely parametric. Full Lite, Half Lite, and Flush Panel doors included. All Hardware included.

No Rating

Product Version: Unknown

8711 Downloads

NOT parametric... however fits all normal sizes of walls. To change materials, go into nested families.

Product Version: Revit Architecture 2011

27024 Downloads

Parametric toilet stall, I was unable to create a door flip switch because the door is a nested family but I created an on/off switch and two families as a work around

No Rating

Product Version: Revit Architecture 2019

8004 Downloads

Simple Door Tag. In order for it to work, you have to create 2 shared parameters in your door family:
Hardware Type & Door Frame Type. Then load this door in to the project and assign letters of your choice to these parameters.

Product Version: Unknown

5292 Downloads

Base Cabinet - 1 Door

*** IMPORTANT: The shared parameters file must be pointed to inside Revit.  All casework families built by myself can point to the same shared parameter file. ***

• Do not adjust parameters under "Other" category.


• Please save the shared parameters file in the same directory as the cabinet family.

Any comments would be appreciated.

No Rating

Product Version: Revit Architecture 2014

7145 Downloads

Base Cabinet - 2 Door

*** IMPORTANT: The shared parameters file must be pointed to inside Revit.  All casework families built by myself can point to the same shared parameter file. ***

• Do not adjust parameters under "Other" category.


• Please save the shared parameters file in the same directory as the cabinet family.

Any comments would be appreciated.

Product Version: Revit Architecture 2014

12300 Downloads

Tall Cabinet - 1 Door

*** IMPORTANT: The shared parameters file must be pointed to inside Revit.  All casework families built by myself can point to the same shared parameter file. ***

• Do not adjust parameters under "Other" category.


• Please save the shared parameters file in the same directory as the cabinet family.

Any comments would be appreciated.

No Rating

Product Version: Revit Architecture 2014

9198 Downloads

Tall Cabinet - 2 Door

*** IMPORTANT: The shared parameters file must be pointed to inside Revit.  All casework families built by myself can point to the same shared parameter file. ***

• Do not adjust parameters under "Other" category.


• Please save the shared parameters file in the same directory as the cabinet family.

Any comments would be appreciated.

Product Version: Revit Architecture 2014

15024 Downloads

I wasn't satisfied with the BIM families from True's website so I created this fully parametric family has all of the T-Series refrigerators including solid door, glass door, and half door styles. All of these models can become freezer or dual temperature units by changing the model numbers in Identity Data.

The only model not included is the "T-23P" Pass-Thru unit because I didn't want to have to make a visibility instance for a void. Maybe I'll update it later. I also plan to add the sliding door units in the near future.

Let me know if there are any issues.

Product Version: Revit Architecture 2013

18273 Downloads

Base Cabinet - Sink, 1 Door

*** IMPORTANT: The shared parameters file must be pointed to inside Revit.  All casework families built by myself can point to the same shared parameter file. ***

• Do not adjust parameters under "Other" category.


• Please save the shared parameters file in the same directory as the cabinet family.

Any comments would be appreciated.

No Rating

Product Version: Revit Architecture 2014

4784 Downloads

Base Cabinet - Sink, 1 Door

*** IMPORTANT: The shared parameters file must be pointed to inside Revit.  All casework families built by myself can point to the same shared parameter file. ***

• Do not adjust parameters under "Other" category.


• Please save the shared parameters file in the same directory as the cabinet family.

Any comments would be appreciated.

No Rating

Product Version: Revit Architecture 2014

7907 Downloads

Base Cabinet - 1 Drawer above 1 Door

*** IMPORTANT: The shared parameters file must be pointed to inside Revit.  All casework families built by myself can point to the same shared parameter file. ***

• Do not adjust parameters under "Other" category.


• Please save the shared parameters file in the same directory as the cabinet family.

Any comments would be appreciated.

Product Version: Revit Architecture 2014

5180 Downloads

Base Cabinet - 1 Drawer above 2 Door

*** IMPORTANT: The shared parameters file must be pointed to inside Revit.  All casework families built by myself can point to the same shared parameter file. ***

• Do not adjust parameters under "Other" category.


• Please save the shared parameters file in the same directory as the cabinet family.

Any comments would be appreciated.

No Rating

Product Version: Revit Architecture 2014

5631 Downloads

Tall Cabinet - 1 Door above 2 Drawer

*** IMPORTANT: The shared parameters file must be pointed to inside Revit.  All casework families built by myself can point to the same shared parameter file. ***

• Do not adjust parameters under "Other" category.


• Please save the shared parameters file in the same directory as the cabinet family.

Any comments would be appreciated.

No Rating

Product Version: Revit Architecture 2014

4859 Downloads

Loosely based on Andersen Windows products. Flexes within certain limits. Mutins created as separate families and do not flex but can be edited and inserted.

Product Version: Revit Architecture 2008

21660 Downloads