My best recreation of the Corwin Dining Table w/Round Top from Epoch West Furniture.  Para diameter.

Made it for my wife who's an interior design student.  Hopefully it helps some other people out there.

Product Version: Revit Architecture 2017

1962 Downloads

Recreation of the 200559 - 8in Diamond Mini Pendant from Meyda lighting.  Overall length (ceiling to bottom of pendant body) is parametric to adjust hanging height.  Set materials for the mica shade and metal frame.

Made this for my wife who is an interior design student.  Hopefully it helps some other people out there.

Product Version: Revit Architecture 2017

1195 Downloads

My recreation of the Herman Miller Magis Spun Chair.

Material can be set.

Please rate and comment!  Thanks.

Product Version: Revit Architecture 2017

784 Downloads

My recreation of the UTU Helio II chandelier.

Material can be set for body 1, body 2, globes, finial, cord, and canopy.

Please rate and comment!  Thanks.

Product Version: Revit Architecture 2017

810 Downloads

Please rate and comment, thanks!

Took a while to figure out how to get these to work properly.

The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.

The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.com

Cans be individually rotated in project.

!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!

Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).

The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.

You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.

I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.

Hope these are helpfull for you!

Product Version: Revit Architecture 2017

1013 Downloads

Please rate and comment, thanks!Took a while to figure out how to get these to work properly.The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.comCans be individually rotated in project.!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.Hope these are helpfull for you!

Product Version: Revit Architecture 2017

619 Downloads

A custom designed single stack wine rack w/ display rack near middle. 5 3/4"w x 1' 1"d x 8' 6"h

Product Version: Revit Architecture 2017

5841 Downloads

My best recreation of the 608C Arm Chair from Old Hickory Furniture.  Non-para.

Made it for my wife who's an interior design student.  Hopefully it helps some other people out there.

No Rating

Product Version: Revit Architecture 2017

549 Downloads

My best recreation of the 608D Side Chair from Old Hickory Furniture.  Non-para.

Made it for my wife who's an interior design student.  Hopefully it helps some other people out there.

No Rating

Product Version: Revit Architecture 2017

411 Downloads

My best recreation of the Butte Chair from Old Hickory Furniture.  Non-para.

Made it for my wife who's an interior design student.  Hopefully it helps some other people out there.

No Rating

Product Version: Revit Architecture 2017

1336 Downloads

My best recreation of the CCRS 007 counter height stool from Epoch West Furniture.  Non-para.

Made it for my wife who's an interior design student.  Hopefully it helps some other people out there.

No Rating

Product Version: Revit Architecture 2017

707 Downloads

My best recreation of the Bannack Dining Table from Epoch West Furniture.  Non-para. 7'L x 4'W x 30"H

Made it for my wife who's an interior design student.  Hopefully it helps some other people out there.

No Rating

Product Version: Revit Architecture 2017

548 Downloads

My best recreation of the Sargent Chandel-Air from Meyda.  54" round, diffuser body, metal trim, fan blades, fan body materials can be set.  Only shaft length (to adjust hanging height) is parametric.

Made this for my wife who is an interior design student.  Hopefully is helps some others out there.

No Rating

Product Version: Revit Architecture 2017

415 Downloads

My best recreation of the Ricardo Conversation Sofa from King Hickory furniture.  Cushion are really hard to make look right! lol

Non-para.  Materials can be set for seat cushion, seat backs, body back and front deck, arms and outside body panel.

Made this for my wife who is an interior design student.  Hopefully it helps some others out there.

No Rating

Product Version: Revit Architecture 2017

1812 Downloads

Recreation of the 16in Smythe Craftsman Flushmount from Meyda lighting.  Non-para.  Materials can be set for metal frame and shade.

Made this for my wife who is an interior design student.  Hopefully it helps some others out there.

No Rating

Product Version: Revit Architecture 2017

310 Downloads

This is a recreation of the Hanck Coffee Table from Epoch West furniture.  Length and width are parametric.  Set materials for top, legs, and body.

I made this for my wife who is an interior design student.  Hopefully it helps some others out there.

No Rating

Product Version: Revit Architecture 2017

642 Downloads

This is a recreation of the Lavina Cricket Table from Epoch West furniture.  Parametric.  Materials can be set for the various parts.

I made this for my wife who is an interior design student.  Hopefully it helps some others out there.

No Rating

Product Version: Revit Architecture 2017

271 Downloads

This is a recreation of the Austin swivel chair from King Hickory furniture.  Non-para.  Materials can be set for body, seat, and seat back.

I made this for my wife who is an interior design student.  Hopefully it helps some others out there.

No Rating

Product Version: Revit Architecture 2017

1564 Downloads

My best recreation of the Charles Ghost barstool from Kartell.  Non-para.  Material can be set, however, the piece is made from molded polycarbonate.

I made this for my wife who is an interior design student.  Hopefully it helps some others out there.

No Rating

Product Version: Revit Architecture 2017

918 Downloads

My recreation of the Heron dining chair by Kelly Wearstler.

Material can be set for frame and seat+back.

Please rate and comment!  Thanks.

No Rating

Product Version: Revit Architecture 2017

1648 Downloads

My recreation of the UTU Helio III chandelier.

Material can be set for body 1, body 2, globes, finial, cord, and canopy.

Please rate and comment!  Thanks.

No Rating

Product Version: Revit Architecture 2017

452 Downloads

My recreation of the NOOM - Suprematic Two CS5 pendant.

Material can be set for cylinder, oval, circle, cord, canopy.

Please rate and comment!  Thanks.

No Rating

Product Version: Revit Architecture 2017

254 Downloads

My recreation of the NOOM - Suprematic Three CS5 pendant.

Material can be set for cylinder, oval, circle, cord, canopy.

Please rate and comment!  Thanks.

No Rating

Product Version: Revit Architecture 2017

196 Downloads

Please rate and comment, thanks!Took a while to figure out how to get these to work properly.The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.comCans be individually rotated in project.!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.Hope these are helpfull for you!

No Rating

Product Version: Revit Architecture 2017

459 Downloads

Please rate and comment, thanks!Took a while to figure out how to get these to work properly.The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.comCans be individually rotated in project.!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.Hope these are helpfull for you!

No Rating

Product Version: Revit Architecture 2017

432 Downloads

Model of SMEG's retro 50's refrigerator.  Model #FAB32ULOR3.

Non parametric.  Materials can be set for the body pieces combined, the logo and handles combined, and the support feet.

I made this for my wife who is and interior design student.  I hope it helps some others out there.

No Rating

Product Version: Revit Architecture 2017

4948 Downloads

Model of the Fairfax chair by Kelly Wearstler.

Non parametric.  Materials can be set for the body pieces combined.  There are a couple minor incongruencies that I was unable to resolve dealing with the cutout in the lower portion of the chair.  Hopefully it doesn't cause any problems.

I made this for my wife who is and interior design student.  I hope it helps some others out there.

No Rating

Product Version: Revit Architecture 2017

8934 Downloads