Forums
|
Forums >> Revit Systems >> Technical Support >> Custom Hatch Patterns on Revit
|
|
|
active
Joined: Wed, Nov 25, 2009
65 Posts
No Rating |
Hi, I´m trying to make a Custom Hatch Pattern by entering codes on a notepad so revit may be able to read it, but I´m just do not know what am i missing following the procedure of info. I just cannot do it not matter what I do including the years and years of trying,  , jajjaja. Would you help me resolving this issue?, I already draw my pattern manually on the 4 fachades of my project, but I preffer to erase those detail lines and let a good custom pattern be part of the drawing. I know this example will help me and all the revit comunity to solve the custom hatch pattern. Thanks a lot and my best wishes...
|
This user is offline |
|
 | |
|
|
active
Joined: Tue, Jan 27, 2004
80 Posts
 |
Here's an INCH version ;%VERSION=3.0 ;%UNITS=INCH *VHUGOMG,Revitcity ;%TYPE=MODEL ;------------------------------------------------------------------------------- ; Pattern written by HatchKit v2.7 Hatch Pattern Editor ; HatchKit v2.7 Hatch Pattern Editor(c) Cadro Pty Ltd 1990-2008. ; www.cadro.com.au/hatchkit/ ;------------------------------------------------------------------------------- 0,0,0,0,3.5 0,0,2.5,0,3.5 90,0,0,0,2.4 If your measurements were in metres note Revit patterns are in MM: ;%VERSION=3.0 ;%UNITS=MM *VHUGOMG,Revitcity ;%TYPE=MODEL ;---------------------------------------------------------------------- ; Pattern written by HatchKit v2.7 Hatch Pattern Editor ; HatchKit v2.7 Hatch Pattern Editor(c) Cadro Pty Ltd 1990-2008. ; www..hatchkit.com.au ;---------------------------------------------------------------------- 0,0,0,0,3500 0,0,2500,0,3500 90,0,0,0,2400
-----------------------------------
Hugh Adamson
www.hatchkit.com.au |
This user is offline |
View Website
|
|
|
active
Joined: Wed, Nov 25, 2009
65 Posts
No Rating |
Wooow, it worked. You´re a genius, thank you very much!
|
This user is offline |
|
|
|
active
Joined: Wed, Nov 25, 2009
65 Posts
No Rating |
Here's an image of the pattern applied to the building. Thanks!
|
This user is offline |
|
|
|
active
Joined: Wed, Nov 25, 2009
65 Posts
No Rating |
Sorry for asking again, but although I'm having progress on making hatch patterns on revit, I cannot make circles on patterns like this one I am uploading. It´s a concrete panels hatch with little circle marks . Would you mind telling me the parameters or coordinates for this pattern, I appreciate your help!.
|
This user is offline |
|
|
|
active
Joined: Wed, Nov 25, 2009
65 Posts
No Rating |
I forgot, the parameters of the lines in the pattern are: 90,0,0,0,1220 0,0,0,0,2440 I just dont know how to insert the coordinates for the circles...
|
This user is offline |
|
|
|
site moderator|||
Joined: Tue, May 16, 2006
13079 Posts
|
You can't make circles in hatch patterns. You could approximate with small lines but...I would not even try.
|
This user is offline |
|
|
|
active
Joined: Wed, Nov 25, 2009
65 Posts
No Rating |
It is possible, have you ever seen the pattern of stones or roof tiles with half circle arc? It really is possible...
|
This user is offline |
|
|
|
active
Joined: Tue, Jan 27, 2004
80 Posts
|
Hatch pattern definitions are made up entirely from straight lines, curves are always approximated by short segments. For example the attached HatchKit pattern approximates a 10mm circular hole with 5 lines (a pentagon). Using a small square would simplify calculations if you wanted to create the hatch pattern with a test editor as their short side segments would then line up in this pattern.
-----------------------------------
Hugh Adamson
www.hatchkit.com.au |
This user is offline |
View Website
|
|
|
active
Joined: Wed, Nov 25, 2009
65 Posts
No Rating |
Thanks man, for attending my second question on this subject. I will really consider to buy a hatchkit tool asap ...and you are a genius! Best Regards...
|
This user is offline |
|
| |
|
|
active
Joined: Wed, Nov 10, 2010
2 Posts
No Rating |
You should try myHatch, its free and it work so well. You need to add some parameter later on, but it is an easy task.
-----------------------------------
Revit Architecture 2011 |
This user is offline |
|
|
|
active
Joined: Wed, Nov 25, 2009
65 Posts
No Rating |
Thank you, I appreciate your advise. I am downloading it right now. Have a nice day!
|
This user is offline |
|
|
|
active
Joined: Mon, Mar 15, 2010
199 Posts
|
Here is DynaPAT which can create any pattern you want in Revit directily.
https://plevit1.blogspot.com/2020/06/dynapat-pattern-maker-for-revit-by.html
A sample pat file which is created by DynaPAT is attached.
EnjoyRevit is back. 
-----------------------------------
want more?
You can get more tips at Enjoy Revit |
This user is offline |
View Website
|
|
|
site moderator|||
Joined: Tue, May 16, 2006
13079 Posts
|
That is a large file! What does the pattern look like?
|
This user is offline |
|
|
|
active
Joined: Mon, Mar 15, 2010
199 Posts
|
"
That is a large file! What does the pattern look like?
"
This is it.
-----------------------------------
want more?
You can get more tips at Enjoy Revit |
This user is offline |
View Website
|
|
|
Similar Threads |
|
Custom Hatch Patterns |
Revit Building >> Technical Support
|
Thu, Dec 23, 2004 at 3:00:33 PM
|
1
|
|
imported acad hatch patterns |
Revit Building >> Technical Support
|
Sun, Nov 25, 2007 at 6:39:03 PM
|
0
|
|
Hiding Hatch Patterns [ 1 2 ] |
Revit Building >> Technical Support
|
Sat, Aug 29, 2009 at 8:12:26 AM
|
15
|
|
How to scale Hatch Patterns already loaded in file? |
Revit Building >> Technical Support
|
Tue, Apr 19, 2011 at 3:11:32 PM
|
8
|
|
Stone Hatch Patterns - Looking for a good source. |
Revit Building >> Technical Support
|
Sat, May 4, 2013 at 4:59:25 AM
|
8
|
|
|
Site Stats
Members: | 2097127 | Objects: | 23163 | Forum Posts: | 152288 | Job Listings: | 3 |
|
Search
83380_concrete_panels.dwg
83410_CONCRETEPANEL.PAT