Forums >> Revit Building >> Technical Support >> Array Parameter
|
|
active
Joined: Tue, May 6, 2008
24 Posts No Rating |
- I am trying to create a parametric louver which has variable number of horizontal blades depending on the size of the louver. The louver has several parameters: width, height, frame thickness. When I create the first horizontal blade and attach it to the frame, I flex the width and height parameters and the blade reacts properly, staying attached to the fame in all cases. I then array the single blade to multiple blades and create an additional "number of blades" parameter so I can manually adjust the number of blades based on the height of the louver. When I flex the new model by adjusting the height or width of the louver, I get an error message saying the constraints are not met and the blades don't stay attached to the frame. The issue is in the array command: even thought the original blade was attached and locked to the frame the new arrayed blades are not. I can't manually attach the other blades as the number is variable. Any suggestions?
|
This user is offline |
|
 |
|
site moderator|||

Joined: Tue, May 22, 2007
5921 Posts
 |
Create the array only with 2 blades, give the parameter and so one, then you must attach with "align" tool the second blade to the ref. planes, then the array must work fine.
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
 |
active
Joined: Tue, May 6, 2008
24 Posts No Rating |
Thank you, the blades are working vertically: the number increases or decreases depending on the height of the louver. But, they do not stay attached to the frame when I alter the width. I attached the ends of the blades to a reference plan at the side frame...but no luck. ????
|
This user is offline |
|
 |
site moderator|||

Joined: Tue, May 22, 2007
5921 Posts
 |
You must check in plan view (change the cut plane to see the 2 blade if you need) if the blade are locked to ALL ref. planes envolved, go to the others elevation/section views and check again, there is something in that second blade it's not locked to the ref. planes.
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
 |
active
Joined: Tue, May 6, 2008
24 Posts No Rating |
In theory if I lock the two original blades properly all of the subsequent blades made from increasing the size of the louver should lock automatically?
|
This user is offline |
|
 |
active
Joined: Tue, May 6, 2008
24 Posts No Rating |
I've tried locking the blades in both plan and elevation, double checked the locks and it still will not stay attached to the side frame @#%$$%$%$!@#(&%&?>, obviously an operator error.
|
This user is offline |
|
 |
active
Joined: Tue, May 6, 2008
24 Posts No Rating |
I've narrowed the issue to the group and associate aspect of the array command, if I have a single blade or if I copy the blades they will adjust properly when I change the louver size. When I array the blades and group and associate them all hell breaks loose. Any help is appreciated. I've attached the file if that helps
|
This user is offline |
|
 |
active
Joined: Mon, Mar 15, 2010
1 Posts No Rating |
I have the exact same issue, was a resolution to this ever found? When I stretch the width the blades (Or even Model Lines) don't get stretched to the new width. Any help is greatly appreciated. Thanks.
|
This user is offline |
|
 |
active

Joined: Thu, Mar 17, 2005
1231 Posts
 |
I too have played with the louvre family. I found that using reference lines worked much better than reference planes.
-----------------------------------
.
FULL 'DOWNLOAD ACCESS' to all 850+ CADclips videos for only $150
|
This user is offline |
View Website
|
 |
 |