Forums
|
Forums >> Revit Structure >> Technical Support >> Metal deck roof profile
|
|
|
active
Joined: Tue, Jun 24, 2008
9 Posts
No Rating |
I have been trying to create a 1 1/2" metal deck roof so when I cut a section I can see the roof profile. I have tried the following link w/o success http://revitfamilies.blogspot.com/ I created the profile using the profile template, then started the new family with the Structural Framing - Beams and Braces.rft. The profile is loaded, and I deleted the solid. What am I supposed to draw with the sweep tool? Is there anything specific I have to do to orient the profile when I load it? This is crucial to the architect to be able to see roof profile when they link our model to theirs thanks for the help bluedog
|
This user is offline |
|
 | |
|
|
site moderator|||
Joined: Fri, Feb 10, 2006
1874 Posts
 |
take a look at this it may help http://revitfamilies.blogspot.com/2008/08/quantify-profiled-roof-sheeting.html hth
-----------------------------------
best regards, coreed,aia bmpArchitects,Inc. "Revit has to be implemented, Not installed." Long Live Revit |
This user is offline |
|
|
|
active
Joined: Tue, Jun 24, 2008
9 Posts
No Rating |
Thanks for the reply, but that is the link I was referencing. I think I need to get a clue on sweeps.
|
This user is offline |
|
|
|
active
Joined: Tue, Jun 24, 2008
9 Posts
No Rating |
I have a workaround, just use a floor family instead of a roof.
|
This user is offline |
|
|
|
site moderator|||
Joined: Tue, May 22, 2007
5921 Posts
|
Hi "Bluedog1", I did several videos about this same question a few months ago, if you search you can find it... Use the Roof>Sloped Glazing system and it work fine....
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
|
|
active
Joined: Thu, May 5, 2011
18 Posts
No Rating |
bump
I too am stuck on the same spot .
"I created the profile using the profile template, then started the new family with the Structural Framing - Beams and Braces.rft. The profile is loaded, and I deleted the solid.
What am I supposed to draw with the sweep tool?"
|
This user is offline |
|
|
|
site moderator|||
Joined: Tue, May 22, 2007
5921 Posts
|
Maybe this can help you, watch the video i post there.
http://www.revitcity.com/forums.php?action=viewthread&thread_id=22937&start=0
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
|
|
Similar Threads |
|
Metal Deck profile question |
Revit Structure >> Technical Support
|
Thu, Jun 1, 2017 at 11:16:20 PM
|
4
|
|
Metal Structural Deck on Floor |
Revit Building >> Technical Support
|
Tue, Jul 12, 2005 at 10:06:29 AM
|
2
|
|
metal deck cut profile |
Revit Building >> Technical Support
|
Thu, Nov 4, 2010 at 9:17:43 AM
|
4
|
|
creating a corregated metal roof |
Revit Building >> Technical Support
|
Mon, Oct 1, 2012 at 1:20:26 PM
|
3
|
|
Metal roof deck on sloped roof |
Revit Structure >> Technical Support
|
Wed, Oct 21, 2009 at 3:33:17 PM
|
1
|
|
|
Site Stats
Members: | 2102404 | Objects: | 23173 | Forum Posts: | 152296 | Job Listings: | 3 |
|
Search