|
Forums >> Revit Building >> Technical Support >> Can Not Make cut-out
|
|
|
active
Joined: Wed, Apr 16, 2008
9 Posts
No Rating |
I'm using 09 Revit. I am constructing a geodesic dome. I only had to model 1/5th of it. I created a square roof that I could add bearing heights and then cut out with vertical opening. I completed the construction of the 1/5. I grouped the opening cut and the roof. No matter what I try. example: I can mirror 4 of the 5 panels just fine but when it comes to the last 5th it tells me "CAN'T MAKE CUTOUT". Thank You, Raun Tinklepaugh DWL Architects
|
This user is offline |
|
 |
|
|
|
site moderator|||
Joined: Tue, May 22, 2007
5921 Posts
 |
Can you put some images here to figure the model?...
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
|
|
active
Joined: Wed, Apr 16, 2008
9 Posts
No Rating |
Here you go! Have Fun!
|
This user is offline |
|
|
|
site moderator|||
Joined: Tue, May 22, 2007
5921 Posts
|
Where are they?
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
|
|
active
Joined: Wed, Apr 16, 2008
9 Posts
No Rating |
I uploaded the file....
|
This user is offline |
|
|
|
site moderator|||
Joined: Tue, May 22, 2007
5921 Posts
|
Hi, you can do ti with "Array - Polar"
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
|
|
active
Joined: Wed, Apr 16, 2008
9 Posts
No Rating |
I did that and it tells me the same thing. Can't cut out.... It's only that one piece.. Did it work for you?
|
This user is offline |
|
|
|
site moderator|||
Joined: Tue, May 22, 2007
5921 Posts
|
Yeah, there is some issues but...
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
|
|
active
Joined: Wed, Apr 16, 2008
9 Posts
No Rating |
I did that and it tells me the same thing. Can't cut out.... It's only that one piece.. Did it work for you?
|
This user is offline |
|
|
|
active
Joined: Wed, Apr 16, 2008
9 Posts
No Rating |
That as far as I get....
|
This user is offline |
|
|
|
|
|
site moderator|||
Joined: Mon, Jan 12, 2004
2889 Posts
 |
I exported 1 segment to DWG, then imported it back into revit in a Mass Family then did the polar array...
-----------------------------------
Regards,
Chris.
Co-Founder | BIM Consultant | Software Designer  B. Arch)
Xrev Revit API Addins | Revit Rants |
This user is offline |
View Website
|
|
|
active
Joined: Wed, Apr 16, 2008
9 Posts
No Rating |
Thank You to all for your suggestions. I actually ended up offsetting the cutline by 1/16. I worked perfectly... Thank You
|
This user is offline |
|
|
|
Similar Threads |
|
Can't make a Two Cut - Square rafter cut on a roof |
Revit Building >> Technical Support
|
Fri, Jan 14, 2011 at 6:20:30 PM
|
4
|
|
make elevation cut line show from diffrent planes |
Revit Building >> Technical Support
|
Thu, Jul 9, 2009 at 2:10:05 PM
|
5
|
|
is there a way to make walls cut floors? |
Revit Building >> Technical Support
|
Mon, Feb 5, 2007 at 9:39:07 AM
|
4
|
|
Revit 2014 perpendicular cut at the end of the truss |
Community >> Newbies
|
Sat, Jun 27, 2015 at 4:39:13 PM
|
0
|
|
Section cut through the imported dwg file |
Revit Building >> Technical Support
|
Wed, Jun 26, 2013 at 4:00:40 PM
|
12
|
|
Search
38643_Test_Geo1.rvt