|
Forums >> Revit Building >> Technical Support >> Cut pattern under graded region or slabs not showing in plan
|
|
|
active
Joined: Thu, Jun 26, 2008
90 Posts
 |
I am using Revit 2009. In plan, the cut pattern of my topography is not displaying under graded regions or slabs. I have modified the "elevation of poche base" in the Site Settings, but this only impacts the display of the site in section. Any assistance is appreciated.
|
This user is offline |
|
 |
|
|
|
site moderator|||
Joined: Tue, May 22, 2007
5921 Posts
 |
Hi, "In plan, the cut pattern of my topography is not displaying", right the "Cut Pattern" it's just to Sections, can you put some screenshots to figure what are you talking about?
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
|
|
active
Joined: Thu, Jun 26, 2008
90 Posts
|
See the attached image. When My plan is cut at or below where a slab intersects with teh topo surface, the plan view does not poche. If I cut through the face created by a pad object the poche will show, but if you cut at or below the line that I have highlighted as "intersection", I do not get a poche of the earth in plan. Thanks for the interest.
|
This user is offline |
|
|
|
active
Joined: Thu, Jun 26, 2008
90 Posts
|
The result makes sense becasue a topo is a surface object, but the earth poche should be able to display in plan beyond the base of the pad.
|
This user is offline |
|
|
|
site moderator|||
Joined: Tue, May 22, 2007
5921 Posts
|
can you put the right image with shade? do you see the pattern in SITE plan?
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
|
|
active
Joined: Thu, Jun 26, 2008
90 Posts
|
I don't see the pattern in the SITE plan. See attached. Everything shown as white in the plan to the left beyond the buildings at the right should have an earth poche.
|
This user is offline |
|
|
|
site moderator|||
Joined: Tue, May 22, 2007
5921 Posts
|
You must pick in the PAD and edit the properties and change the material and the cut and surface pattern equal like the topo site...
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
|
|
active
Joined: Thu, Jun 26, 2008
90 Posts
|
I don't see the pattern in the SITE plan. See attached. Everything shown as white in the plan to the left beyond the buildings at the right should have an earth poche.
|
This user is offline |
|
|
|
site moderator|||
Joined: Tue, May 22, 2007
5921 Posts
|
Can you see?
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
|
|
active
Joined: Thu, Jun 26, 2008
90 Posts
|
On this attachment, look at Level 1. At Level 1, below "pad A" and "pad B", I should get an earth hatch, just like on Level 2 below "pad B". In plan, if you do not cut through the center of the pad vertically, like Level 2 is here, you don't get a hatch.
|
This user is offline |
|
|
|
|
|
site moderator|||
Joined: Tue, May 22, 2007
5921 Posts
|
I think the problem isn't in the "Hatch" in the plan but it's because the "View Range" in LEVEL 1, because in LEVEL 2 we can see the hatch (level 2 is more height than level1) so try to see VP>View Range.... or can you put the model here to download to see what a hell is going on?
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
|
|
active
Joined: Thu, Jun 26, 2008
90 Posts
|
I have attached two files, one is a diagram. The area in b lue should be hatched. I have also attached the site Revit file.
|
This user is offline |
|
|
|
active
Joined: Thu, Jun 26, 2008
90 Posts
|
I can't upload the revit file. I'll have to set up a test file. I'll do that later. Thanks for your help.
|
This user is offline |
|
|
|
site moderator|||
Joined: Tue, May 22, 2007
5921 Posts
|
Because you only have 2 Mb to upload the file....
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
|
|
site moderator|||
Joined: Tue, May 22, 2007
5921 Posts
|
My email is "thyphoon38@gmail.com"
-----------------------------------
I Hope and I Wish to LEARN more, and more, and more.... REVIT |
This user is offline |
|
|
|
Search
41114_sitepoche.pdf
